Posts Tagged ‘Palm Harbor’

Your Clearwater Heat Pump Settings and Your Comfort Level

Wednesday, January 4th, 2012

Your Clearwater heat pump has a number of settings that can affect your overall comfort level. One of those settings is the fan – which can be set to run automatically when heating is needed or left on continuously so that the device never turns off. Which is better for your home, though? Let’s take a look.

Comfort vs. Economy

The reason there are two settings on your heat pump is that one is more economical. The auto setting allows the device to minimize how often it is on. So, it only turns on when the house needs warm air to maintain the thermostat setting.

On the other hand, the always on setting is designed to provide better comfort. When you leave your heat pump’s fan on continuously, it provides steady heat over time. This means that the temperature remains consistent and mixes the air to ensure there are no uncomfortable pockets of poorly conditioned air in your home somewhere.

Which Is Better?

In terms of comfort level, it depends on your needs. If you’re not too picky about the exact temperature of your home, the auto setting is best because you will save money and it tends to be fairly accurate. However, if you want to ensure you and your family are perfectly comfortable, regardless of the weather outside, the always on setting is the best way to achieve this level of comfort.

Of course, if you’re concerned about the added cost of leaving the heat pump fan on all the time, you can adjust the thermostat to even out the cost. By raising the thermostat 2 degrees in the summer and lowering it 2 degrees in the winter, the added cost of running it constantly should be offset. If it isn’t, you should have your device inspected to ensure both of the settings are properly calibrated.

Tags: , , , ,
Posted in Heat Pumps | Comments Off

Your Tampa Heat Pump’s Settings and Your Comfort Level

Monday, December 19th, 2011

Your Tampa home’s heat pump has a number of settings that can affect your overall comfort level. One of those settings is the fan – which can be set to run automatically when heating is needed or left on continuously so that the device never turns off. Which is better for your home, though? Let’s take a look.

Comfort vs. Economy

The reason there are two settings on your heat pump is that one is more economical. The auto setting allows the device to minimize how often it is on. So, it only turns on when the house needs warm air to maintain the thermostat setting.

On the other hand, the always on setting is designed to provide better comfort. When you leave your heat pump’s fan on continuously, it provides steady heat over time. This means that the temperature remains consistent and mixes the air to ensure there are no uncomfortable pockets of poorly conditioned air in your home somewhere.

Which Is Better?

In terms of comfort level, it depends on your needs. If you’re not too picky about the exact temperature of your home, the auto setting is best because you will save money and it tends to be fairly accurate. However, if you want to ensure you and your family are perfectly comfortable, regardless of the weather outside, the always on setting is the best way to achieve this level of comfort.

Of course, if you’re concerned about the added cost of leaving the heat pump fan on all the time, you can adjust the thermostat to even out the cost. By raising the thermostat 2 degrees in the summer and lowering it 2 degrees in the winter, the added cost of running it constantly should be offset. If it isn’t, you should have your device inspected to ensure both of the settings are properly calibrated.

Tags: , , , ,
Posted in Heat Pumps | Comments Off

A Guide from Tampa: What to Expect in a Low, Medium or High Efficiency Furnace

Monday, December 12th, 2011

When buying a new furnace in Tampa, you have many options. You can purchase a low end model to save money up front and you’ll still get exceptional fuel efficiency, but as you go up the scale, more innovative, money saving features become available. Here is a brief look at what you can expect based on which type of furnace you purchase.

Low Efficiency Furnace

This is a bit of a misnomer as even entry level furnaces have efficiency ratings of at least 80%. For comparison, if you’re still using an old gravity furnace, your efficiency rating could be lower than 50%. Modern furnaces are built to conserve, and while you won’t receive all of the bells and whistles that tend to accompany high efficiency models, you will get a durable, affordable furnace that will last for 10-20 years.

Medium Efficiency Furnaces

Furnaces in the mid-efficiency range have AFUE ratings of between 85% and 92% and are therefore significantly better than those in the entry level range. They also have some of the higher end features available in high efficiency models like programmability and the option for zone control. Because they are still mid-range, they are affordable without skimping too much on features too – a must for any homeowner wanting to save money on both ends.

High Efficiency Furnaces

The highest efficiency furnaces on the market are very different from those you would have purchased even just 10 years ago. Top end furnaces can carry AFUE ratings of up to 95% with a boat load of added features to conserve energy. These features include two stage gas valves so you can maintain a low BTU heating system for most of the year but crank up the heat when the temperature outside drops too low. They are also programmable, which allows you to easily change the temperature settings, fan speed and more from anywhere in the house.

And while they cost more to install, high efficiency furnaces use less energy over their lifespan, last longer and are more environmentally friendly than any other furnaces on the market today.

Tags: , , , , ,
Posted in Heating | Comments Off

Basic HVAC Terminology: Some Tips From Palm Harbor

Wednesday, September 7th, 2011

Ever try to look up basic information about your heating and air conditioning systems in Palm Harbor? There are dozens of terms that might as well be Greek for all you know – a mishmash of words and phrases talking about energy efficiency and air flow ratios. To make your next upgrade a little easier and give you a baseline with which to work, here are a few of the most common HVAC terms you’ll hear in the industry:

  • AFUE (Annual Fuel Utilization Efficiency): This is a simple measurement of how much fuel a furnace converts into actual heat in your home. So, if a furnace converts 92% of the fuel it consumes into heat, it has an AFUE rating of 92.
  • Watts: A single watt is a measurement of electricity. Commonly, your electricity use is assured in kilowatts or kilowatt hours (kWh).
  • BTU (British Thermal Unit): A BTU is a common measurement of how much energy is produced or consumed by an appliance. When referring to an air conditioner, one ‘ton’ refers to 12,000 BTUs.
  • SEER/EER: Seasonal Energy Efficiency Ratio refers to how many BTUs can be produced with a single Watt of electricity per hour. So, an air conditioner with an SEER of 14 can produce 14 BTUs of cooling per watt consumed each hour.
  • HSPF ( Heating Seasonal Performance Factor): Refers to the efficiency of the heating elements in your heat pump.
  • COP (Coefficient of Performance): A measurement of how effective your heat pump is at heating a space compared to standard electrical resistance heat. The lower the temperature gets outside, the lower the COP will be. Equipment is usually measured for COP at 47 and 17 degrees to give an idea of seasonal performance of a new heat pump.
  • Refrigerant: Refrigerant is any gas that is used to draw heat from the air in a particular environment through an air conditioner or heat pump. It has a much lower boiling point than water, allowing it to cool despite the temperature outside. Currently, most equipment uses R-22 refrigerant while the new standard will be R-410A (Puron), legally required in all cooling units by 2020.
  • CFM (Cubic Feet per Minute): Used to measure the volume of air passed through an air handler by an air conditioner or furnace.

There are a number of complicated details to keep track of when choosing a new air conditioner or furnace. To ensure you get the very best out of your system, read up on these details in advance – you’ll feel a heck of a lot smarter when you call.

Tags: , , , , ,
Posted in Air Conditioning, Heating | Comments Off

When Should You Check Your AC Filters: Some Recommendations From Palmetto

Friday, September 2nd, 2011

The filters on your air conditioning unit are vital for keeping out the dust and debris that make things like illness, allergies and air quality worse in your Palmetto home. And it’s important that you take personal responsibility for checking those filters. Sure, you have a professional visit your home once a year to check the air conditioning, but you should also check the system yourself on a semi-regular basis for possible filter degradation.

Monthly Checks

So, how often should you check? Think of it this way. There is no such thing as checking too much, but you can easily not check often enough. So, we recommend checking your filter at least once every 4 weeks. It may not always need to be changed during that four week checkup (sometimes it can last 6 weeks or longer), but it’s good to take a peek.

Why is this so important? Because filters that haven’t been checked and changed as needed have a habit of building up excess sediment and debris. Not a problem when it comes to actually working, but a huge problem when it comes to your energy bill. The harder a system has to work to keep you house cool, the more energy it draws and the more you pay to have cool air in your home. And it will break down much faster as a result of overwork and dirty filters.

Changing an AC Filter

If your filter is ready for a swap, here are some quick tips to get the job done:

  • Find Your Filters: If you don’t know where your filters are, ask your contractor on the next visit or look near the return grills by the thermostat.
  • Remove the Filters: Open the latches and pull the old filter out to check it. You should be able to see clearly through a permanent filter and a disposable one should still be white. If this isn’t the case, it’s time for a cleaning/replacement.
  • Clean the Area: Clear the grill and area of any debris and sediment that might make the filter worse after replacement.

Proper filter maintenance only takes five minutes and it will save you money every month you run your AC – not a bad deal for a few minutes’ work.

Tags: , , , ,
Posted in Indoor Air Quality | Comments Off

Turn that Thermostat Down a Degree and Save Money: A Tip From Gulfport

Monday, August 1st, 2011

There are literally dozens of things you can do to cut back on your heating (and cooling) costs, whether you live in Gulfport or Largo. These range from things like getting a high energy efficiency system to just making sure that you have adequate insulation in all parts of your house. But too many people overlook one of the simplest things that you can do to cut down on your monthly heating bill, and that is to turn the thermostat down.

Of course, you did not pay for that high tech home comfort system just so that you could walk around cold all winter long. You certainly want to keep your house at a temperature that is comfortable, but what does that really mean?

The normal default setting for a home heating system is usually somewhere between 72°F and 75°F. If you have your thermostat set somewhere in this range in the winter, you are probably quite comfortable indoors. In fact, you might not even need a sweater. But would you really notice if it was a degree or two cooler? Would it be incredibly inconvenient to put on a sweater or sweatshirt after all?

The truth is that most of us will be just as comfortable at 69°F as we are at 72°F, and the effect that small adjustment can have on your heating bill is actually pretty significant. In fact, you will save an average of 3% on your monthly bill for every degree you turn your thermostat down. Drop the temperature down by three or four degrees and that will give you up to a 10% monthly savings – hardly something to turn up your nose at.

And setting the regular temperature in your house a bit lower is not the only way your thermostat settings can save you money. You will also save quite a bit if you take the time to turn down the temperature when you leave the house and when you go to bed at night. There simply is no reason to pay to heat your house when you are not there and you will certainly be rewarded with a lower energy bill for your efforts.

Tags: , , , ,
Posted in Air Conditioning | Comments Off